HAM 30-2381
15xD
solid carbide deep hole drill
Product information
- special 4-facet ground
- special point ground
- special chip flute geometry
- 4 guide chamfer
- interior coolant
- shrink fit
- High Performance Cutting
- HSF - Hybride Surface Finishing
Available in many variants
Material Properties
Material
wrought aluminium alloys
casting aluminium alloys
steel < 800 N/mm²
steel < 1200 N/mm²
steel < 1600 N/mm²
steel < 55 HRC
steel < 60 HRC
steel < 66 HRC
stainless steel < 800 N/mm²
stainless steel > 800 N/mm²
lamellar graphite cast iron
spheroidal graphite cast iron
high-temperature alloys
titanium
non-ferrous metals / copper alloys
graphite & fibre composite
MQL
maximum cooling
without cooling
AIR
very suitable
limited suitable
Properties "HAM 30-2381"
| clamping surface: | HAK |
|---|---|
| cutting direction: | right hand cutting |
| head coating: | yes |
| internal cooling: | yes |
| length-to-diameter ratio: | 15 x D mm |
| nominal diameter tolerance: | H7 |
| saft diameter tolerance: | h6 |
| spiral type: | right hand helix |
Article No
Nominal Ø
(d1) [mm]
(d1) [mm]
Shank Ø
(d2) [mm]
(d2) [mm]
Length
(l1) [mm]
(l1) [mm]
Flute Length
(l2) [mm]
(l2) [mm]
Cutting Length
(l3) [mm]
(l3) [mm]
Stock
HAM 30-2381-0300
3.00 mm
6.00 mm
95.00 mm
51.00 mm
45.00 mm
21
HAM 30-2381-0400
4.00 mm
6.00 mm
110.00 mm
68.00 mm
60.00 mm
6
HAM 30-2381-0450
4.50 mm
6.00 mm
120.00 mm
76.50 mm
67.50 mm
9
HAM 30-2381-0500
5.00 mm
6.00 mm
125.00 mm
85.00 mm
75.00 mm
4
HAM 30-2381-0550
5.50 mm
6.00 mm
135.00 mm
93.50 mm
82.50 mm
22
HAM 30-2381-0600
6.00 mm
6.00 mm
140.00 mm
102.00 mm
90.00 mm
4
HAM 30-2381-0650
6.50 mm
8.00 mm
150.00 mm
110.50 mm
97.50 mm
14
HAM 30-2381-0700
7.00 mm
8.00 mm
160.00 mm
119.00 mm
105.00 mm
3
HAM 30-2381-0800
8.00 mm
8.00 mm
175.00 mm
136.00 mm
120.00 mm
5
HAM 30-2381-0850
8.50 mm
10.00 mm
190.00 mm
144.50 mm
127.50 mm
4
HAM 30-2381-1000
10.00 mm
10.00 mm
215.00 mm
170.00 mm
150.00 mm
1
HAM 30-2381-1200
12.00 mm
12.00 mm
255.00 mm
204.00 mm
180.00 mm
4
HAM 30-2381-1400
14.00 mm
14.00 mm
285.00 mm
238.00 mm
210.00 mm
7
Description
| length-to-diameter ratio | 15 x D mm |
| Spiral type | right hand helix |
| Cutting direction | right hand cutting |
| Clamping surface | HAK |
| Head coating | yes |
| Internal cooling | yes |